NI USB-TC01 thermocouple socket parts
Does anyone know the part number for the thermocouple socket pcb on the USB-TC01 temp.sensor?Need to replace it due to its worn out.
View ArticleDoes NIDAQ 6009 support clocked operation?
Hi,I am using NIDAQ 6009 to output two analogue voltage. code followed:"s =...
View ArticleClik here to view.
error -200452 DAQmx Create Timing Source.vi analog output (NI PXIe-4322)
Hello, I'm using a Hardware Timed Single Point to write Data to a Analog Output card (NI PXIe-4322). It would of course be better if I could sync the loop with the output clock. However I get the Error...
View ArticleNi MyDaq as source for a simple transformer
Hello, I want to use my Ni MyDaq as source for a simple transformer consisting of two coils with N1=300 and N2=400 windings, the wire has a diameter of 0,2 mm. They are winded around an iron screw...
View ArticleNI USB-6218 Intermittent Connection
Hi, I've been using an NI USB-6218 and a few days ago it started behaving oddly. The basics of it is that apparently it's being detected by the NI MAX, but it constantly "refreshes" this connection (as...
View Articlenewbie question: Acquiring acclerometer signal
Hi NI community, I have an at-mio-16e-10 DAQ board. I want to acquire 3 different accelerometer signals from single axis accelerometers. At this point, I have the DAQ board set-up, I am kind of...
View ArticleTrying to trigger a camera with USB-6001 in VB6
As the subject line states, all I'm trying to do is use a USB-6001 to trigger a camera to take a picture when I press a button. It takes a 5V TTL signal to trigger, on the rising edge. The problem...
View ArticleCan't provide Iex for PT100 RTD using NI 9217
Hello, I'm trying to setup a PT100 RTD using the NI 9217 C-Series module but according to my multimeter (probes connected to RTD+ and COM on channel 1), there is no current flow. Also, Labview won't...
View ArticleAny way to run a cDAQ-9171 with LV 8.2?
I tried the tricks listed for LV 8.5, but they don't work with 8.2...- If there is no way to run with LV 8.2, is 8.5 the lowest version that will operate the cDAQ-9171? (using the 9.3/9.5 partial...
View Articleexample
i want to take the output of two sensors tgs823 and tgs825 with the same daq usb-6210 using labview but i am not getting any code for this can you please help me for this i already determined the...
View ArticleMeasure the State of a PFI line that is triggering a DAQ Task
I am using a PCIe-6353. I am creating some digital waveform outputs (port0/line0 and port0/line1) and I am setting these outputs to be triggered with a PFI (PFI5). Is there any way to monitor the state...
View ArticleCheap technicians' test bench for 24V component validation - what's the answer?
What's the most practical solution to getting 24V data acquisition, for the purpose of validating analog scaled data from sensors and sinking discrete inputs, without deploying an expensive controller?...
View ArticleCannot connect WLS-9163
Hello,I want to set up an NI WLS-9163 with an NI 9205. However, the Measurement & Automation Explorer does not detect any device when I plug the NI WLS-9163 with an Ethernet cable.I tried every...
View ArticlePXIe-4463 Programming Example
Hi, I am given a task to generate sine wave using PXIe-4463, in LabView, but I found an example in LabView for the NI-DAQmx that will program the device to output sine wave (Hardware Input and Output...
View ArticlecDAQ‑9184 Chassis
Hello, anyone can help me. I havecDAQ‑9184 Chassis and the modules are NI 9211, 9203, and 9205. My project is about tomonitor temperature, light intensity and production rate. Can anybody help me how...
View ArticleNI-6363 USB and DAQmxCreateAIVoltageChan
Hello, I have a question regarding the "DAQmxCreateAIVoltageChan" function (NI-DAQmx). For input parameters, the documentation indicate "minVal" and "maxVal" which are respectively the expected minimum...
View ArticleClik here to view.
How do I calculate the power and temperature of this microwave signal...
Hi all! I'm working on building a radiometer. The ultimate goal is to measure the temperature of the desired object. To do that I have to first know the power radiated by that object.My solution is to...
View ArticlePCI-6032E Testing
Hi Folks, I have a used PCI-6032E running in an external PCI card cage next to a PCIe-6353. The 6353 works fine, no problems. The 6032E was a used card and has never been used in anger. It's hooked up...
View ArticleNI 9265
I am having trouble getting my NI DAQ 9265 to output current. I have done the self test and reset the device and it said it passed but i am not getting a reading on my oscilloscope. Can someone help me...
View ArticleHow to read data of a USB-6000 with C/C++
Dear,I am new in this field and I need to read data of a USB-6000 DAQ with C/C++ language of this device. Could someone help me to start it? Thank you
View Article