Error 1003 VI broken because DAQmx create Channel DO-Digital Output.vi broken...
HeyVI_BROKEN (0): [VI "DAQmx Create Channel (DO-Digital Output).vi" (0x02a8c080)]Not when IDE installed on PC. So: no problem when running on PC where LabVIEW developement is installed. Tried LV2014...
View ArticleClik here to view.
NI DAQ USB-6009 - Low Input Impedance
Hi, looking through the specs sheet of NI DAQ USB-6009, we notice the remarkably low input impedance of 144kOhms. Take the following circuit diagram of a transimpedance amplifier with a photodiode set...
View ArticlePCI card to PCIe slot adapter
Hello, My computer board only has PCIe 16X and 1X slots, which doesn't fit the PCI card. Does NI have any PCI card to PCIe slot adapters or where can I find one? Thanks in advance!Best,Xavier
View ArticlecDAQ-9181 with APIPA no longer detectable on network after power cycle
Hi,fair warning... This is not a clean cut question -> answer... I'm a little out of my depth with this network error stuff. Also, there is a high probably this is a network/windows problem and in...
View ArticleHow to connect NI9205 with PEM Fuel Cell
Hi, I am relatively new at using the NI9205 and also the LabView program. My question is, I would like to measure voltage and current of PEM fuel cell that is connected to an electronic load. Can...
View ArticleSample Clock and DAQmx Read
Using 9219 Previous programmer sets the Sample Clock with the following parametersSample Mode = Continuous SamplesRate = 100number of samples = 90000 He starts the Task. Then in a While loop, he uses...
View ArticleUsing USB-6361 To Convert Sine to TLL
I’ve recently acquired a USB-6361 with BNC connections. I’ve read many posts on the Community and looked through the documentation, but I’m confused on how to configure the DAQ for my application. What...
View ArticleRecommendation for Hardware-Timed USB DAQ for Digital Input Acquisition
Good day, everyone! I'm a student and quite a newbie to the world of NI stuff, so any and all help would be gladly appreciated. I'm looking to find the most affordable USB DAQ option for high frequency...
View ArticleProgramming USB6000 DAQ to generate signals, without LabView
Hello,[context]I am using a USB6000 DAQ to acquire analog signals *without Labview* (I don't even have a LabView license). I am using the DAQmx .NET SDK, it works pretty well in a custom software....
View ArticleNI 9211 slow response with cDAQ modules
Hi everyone, I have a NI cDAQ 9178 and a thermocouple acquisition card NI-9211. I just want to acquire temperature measurements at 2 Hz. However, when I create a task with DAQ assistant asking for one...
View ArticleLabview Code not recognizing replacement USB-6363 unit
Hi, I would like some advice on getting an USB-6363 DAQ to work with my Labview code. Background: I have an existing Labview code that worked beautifully with a USB-6363 unit. I replaced this unit...
View ArticleVoltage vs Temeprature 9211
Hi all, i have a 9211 to read a thermocouple, if i configure all 4 chanel, with daqmx vi, the instrument to read the thermocouples everything works fine. I need of channel voltage, an idea is to...
View ArticlePCI 4472B versus USB 4432
can I replace a PCI 4472B with a USB 4432 ?what are the differences ? what issues might i encounter ?
View ArticlecDAQ-9188
cDAQ-9188 failed when Max run selftest - not actived. Ping IP address is OK, Max can see sub boards, but it doesn't pass selftest. checked power led is lighting, status and active leds are dark....
View ArticlecDAQ-9185 如何回复出厂设置
有2个 cDAQ-9185 ，网络采集不稳定，改成固定ＩＰ后其中一个机架掉线Ｘ，重新启动加算计，结果连个都失联，再次启动计算机，并停电，结果全都失联。请问：如何回复出厂设置？
View Article6280 output data with spefied frequency
Hello! I am using the PXIe 6280, I need to send 16 bits data to the digital outputs from the host PC using labview.The problem is that i cannot control the timming of these data at the output ports....
View ArticleRelay control
Hi All, Was looking for some advice on driving a relay using Digital output from the NI USB 6002.As I understand from the manual/spec this is an open collector output. Am I correct in thinking each...
View ArticleAI, DO, TC with single DAQ
Hello everybody,for a project I am developing I need to do the following:- acquire analog inputs from pressure transducers (4x)- send digital outputs to control solenoid valves (2x)- acquire...
View ArticleMeasuring voltage points from USB6210
Hi all, for this task I must measure 7 test point voltages and make sure they are within a certain range. I am using the USB 6210. I have never written a labview application before and was wondering if...
View ArticleSPI interface with NI USB-6251
Hi,We are using an ADC which has an SPI interface. We have NI USB-6251Shall we use this DAQ for communicating with the ADC ??What are the steps involved in implementing this ?Any document/link...
View Article