LM35 with usb 6008
could I use LM35 to measure surface temperature of solar cell ? won't it be affected by air temperature ?
View ArticleError while running LabView and Matlab on the same card
I am trying to output a sine wave through an AO channel (using Matlab function analogoutput) on a NI DAQ card and have it read on an AI channel on the same DAQ card through a LabView executable. The...
View Articleni daq 6008 with matlab
i am doing sensor measurement using ni usb 6008 and i made the configuration to be single ended channel the range should be changed to +10 to -10 but that didn't happened , I also connected the same...
View ArticleErro: R6016 - "NOT ENOUGH SPACE FOR THREAD DATA" Após ~48h rodando aplicação.
Boa tarde a todos, Estou desenvolvendo uma aplicação para controle de um banco de testes. Utilizo hardware cDAQ, tanto para o controle dos atuadores, quanto para a leitura dos sinais dos sensores...
View Articlewaiting for task to complete
I inherited a program that intensively tests a hardware device. One of the tests turns each AI channel on and off multiple times and reads the waveform of the AI channel. I am using a DAQ PXI 6229...
View ArticleLooking to synchronize NI 9215 with USB 6361
Hello all, I am looking to synchronize a USB 6361 and a ENET-9163/9215 so I can collect data at different datarates from two different datacards. For example, I am planning on collecting 200kS/s on...
View ArticleClik here to view.
NI-6210 Signal Noise
Hello,I am having an issue with some signal noise and I want to be sure I have made the connections properly. As shown below, I have connected a loadcell amplifier to the NI-USB 6210, and connected the...
View ArticleHow to connect 40 differential analog input signals to USB-6255 using SCB-68...
Hello I have USB-6255 DAQ which required external SCB-68 for instrumentation.I have 8 SCB-68 devices but at a time i can connect only 2 SCB-68 device to USB-6255. In my application, i need to connect...
View ArticleCan't get nidaqmx.tlb installed
I was, until this morning writing an application on VB6.0 which used the USB-6501 via the nidaqmx.tlb file which was in Windows\System32.I then decided that I would make it a .Net application in C#...
View ArticleNeed NI 9205 module to read pressure transducer
Hello, I have a NI 9205 I am using to read the data from a 3 wire pressure transducer. However I am not sure how to connect it properly. I have a the + signal wire going into the NI 9205 AI0 port. The...
View ArticleClik here to view.
NI 9213 Changing from High Resolution to High Speed. Screen caps included.
Hi, I have a 9213 card in a CRIO 9074. My sampling rate is exactly 1S/s which means that it is running in high resolution mode. However when I go into the project window and change it to high speed (as...
View ArticleLogdata method in ...IntClk_ToFile example
....IntClk_ToFile example I am trying to understand how the following function writes data to a file. It does not seem to be associated with a filestream. What am I missing? Thanks! private void...
View ArticleError -50103 with DAQmx PCI 6225
I'm currently using a PCI 6225 Card. I intend to create multiple tasks running concurrently.One task will log data in TDMS file and read a set of analog inputs continuously andanother task will only...
View ArticleTriggering
I am having NI USB 6008. With this how can i Generate a Trigger output in the range of 10us... Is there any to generate Trigger output in my NI USB 6008????
View Articlewindows 7 64-bit compatibility with PCI 7813R & PCI6225 cards.
We have a desktop PC that runs Windows 7 (64-bit). Is the 64-bit Labview 2012 version compatible withPCI 7813R & PCI 6225 cards?
View ArticleWhat is the minimum noise level of 9263 AO? And how to reduce the noise?
Hello, I used many 9263 analog output modules. Most output signals control current servo circuit. The current servo is designed for 1 V output voltage = 1 A. However my output current from current...
View ArticleConnect PXI4461 with PXI4498
Hey Guys,I am new to this forum. Basically got a problem and hopefully you could help me.I have one PXI 4461 and one PXI4498. I intend to use PXI4461 as a signal generater while PXI 4498 as the...
View ArticleProcessing data Productor/consumer
Dear all,I have a LV project which takes 16 differents signals using NI-9205. The datas are currents and voltages, while I've acquired all the values, I need to process them doing filters, rms,...
View ArticleError 9313
When I launch the NI ELVIS, error - 9313 occurred at ELVIS Instrument Launcher. Possible reason(s):"NI ELVIS: DAQmx is not installed on your machine. Please install DAQmx. I have checked and I have the...
View ArticleHow do I change temperature values stored on card?
The data I'm referring to is the stored Last Self Calibration and Last External Calibration temperature values. I have a PCI-6052E card that fails calibration at the Self Calibration step, possibly due...
View Article