Unable to install DAQmx 9.5.1 on labview 8.6
Hi,I'm trying to install a PCI 6034E card (only option available to me) on a Windows 7 (64 bit) PC with Labview 8.6. A force transducer I need to use requires DAQmx 9.5.1 to be installed, however when...
View ArticleFunction Generator to check phase sync between two AI channels
Is there any way to connect a function generator or with an oscilloscope with a NI module to see whether the sinewave graphs of two analog input channels are not loosing phase for sync purposes? For...
View Articlerobotics
Hi , I am using c35018 transistor to control current flow over the solinoid with labview interface and DAQ , but i am facing issues that when current increase above 2 amp te transister burns , is there...
View ArticleHas anyone successfully loaded NI-DAQmx 8.0.2 in Ubuntu OS system version 12...
I understand that NI-DAQmx 8.0.2 - National Instruments is for RedHat and SUSE, but has anyone tred to enable it on Ubuntu OS system?<script...
View ArticleMagnetic Reed Sensor
Hi all, I want to use a Magnetic Reed Sensor, OMAL RV21, to a DAQ sensor.Can someone recommend me a module to work with it? and can I use the NI-9205? Tnx!
View Articledaq system is running slow
Why is it taking a minute for my NI 9205 DAQ to read the incoming data from solution.
View ArticleClik here to view.
synchronizing USB 6351
Hello, I have a question related to synchronizing two USB 6351 DAQ boards. I routed the sample clock and a start trigger from one device to the other (as in the attached picture of the code), and ran...
View ArticleDAQ mx: continuous mode and the buffer size
I've been working on a program in Labview which reads out voltage from my device. For that I use the the DAQmx Timing sub VI as shown in the picture.DAQmx connect. I want do display the voltage in each...
View Articlesmallest voltage change detectable
Hello,A simple question, but the help is appreciated. My 6289 m-series ADC is 18 bit. I am performing AI Voltage with LV8.5 DAQmx Read (Analog 2D I32 NChan NSamp).vi For +/-10V input range, is the...
View ArticleClik here to view.
Error 200019
Hello,I found many posts about this problem here but can't find solution. I have NI X USB 6343 ( 32 - channels, max rate 1-channel - 500 kS/s). I'm using only one channel, I trying to set rate about...
View ArticleDifference between reset in NIMAX and DAQmxResetDevice
I am using a PXI-6259 (M Series) and am doing different low-level software signal routing within the board for various experiments. When I switch between experiments I reset the board in NI-MAX to...
View Article9205 all channels reading together
We have a 9205 in a 9188 xt reading 16 pairs of differential signals, 0-10vdc. This is setup as spares so they're technically not connected to anything but an open connector. When shooting in a voltage...
View ArticleSCXI-1001 & LabVIEW 7.1 Upgrade
Hi all, First off, I'm no means an expert. Sorry in advance if these questions make me sound like im an idiot........ and thanks for your help. I have 4 test cells with identicle setups. Here is a list...
View Articleposition measurement using linear encoder
Hello, I have a position sensorhttp://www.elgo.de/pdf/manual/sensors/LMIX1-000-E_06-09.pdf which has output signals A, B and Z. In my case, the signal is 10...30 V HTL. (page 10 of PDF). Can anyone...
View ArticleList of Traditional NI-DAQ error codes
Is there a list of the Traditional NI-DAQ error codes? I found one for the NI-DAQmx in NIDAQmx.h, but I can't find anything online for the Traditional.
View Articleindividual control of analog output channel CDaq with NI9264
Hello All, I am using a CDaq 9174 with 9205 + 9264.I would like to control individually 5 of the AO channel depending of what is happening on the analog input (9205). Actually, I want to output 0V if I...
View ArticlePCIe-7842R (R series FPGA) digital output not work properly
Greetings, I'm having some problem outputing correct TTL voltage with my PCIe-7842R FPGA board. The block diagram of my orignal LV FPGA code is shown in "analog to digital.png". The idea was to convert...
View ArticleNI-9191 and Crio-9075
Hello..I would like to know if I can see my NI-9191 Wireless chassis through my CRio-9075?I have my CRio-9075 connected to a wireless access point and the NI-9191 to this acces point too...The Idea is...
View ArticleWindows 10 -- myDAQ Driver Not Working
Hello, I just "upgraded" to Windows 10 and installed everything required for myDAQ and Windows isn't recognizing the driver. Has anyone else had this issue and found a fix? I installed the most recent...
View Article