daqmx error code -200561--solved remove
What is this code mean?something to do with "Attempt"?DAQ PXI 6230C/C++where do I find the error codes?Thanks I found the error code, the data I'm attempt to write is to small or to large for the...
View Article求助：NI USB 6353数据采集卡测试数据不准确
用NI USB 6353数据采集卡测试电压信号，数据在测试值与10.588V之间不断震荡，而且频率较高，改变测试信号值依然停留在10.588V，但是用NI的其他采集卡采集该信号可以达到要求。用6353采集卡采集信号发生器发出的信号可以完整输出。不知道是采集卡的问题还是程序问题，跪求大神解答！
View Articlechannel shift
I'm using a USB-6259 and have configured a task in MAX for Ai1, Ai2, Ai3, Ai4, Ai5, Ai7, Ai8, Ai9, Ai10, Ai11 and when I run the task under MAX the channels are shifted down one meaning the table view...
View ArticleArduino 2 and LabView
Hi everybody,I'm trying to use the new ARDUINO DUE board as a DAQ in Labview so I followed instruction here:http://digital.ni.com/public.nsf/allkb/A20FBBD36820669086257886004D5F4D?OpenDocument ..but,...
View ArticleSimultaneous analog input and thermocouple acquisition using the NI cDAQ-9172...
Hi all, I've been struggling for some time trying to get the simultaneous acquisition of analog voltage and thermocouple data to work. Solely, the analog input works just fine but when the code for...
View ArticleDAQmxCfgSampClkTiming sampsPerChanToAcquire limit
I am using a PCIe 6321 & 6363 board. When I set the the sampsPerChanToAcquire above 2^31 samples I get an error 'invalidAttributeValue'. However the parameter signature is an int64. Is this...
View ArticleComment installer NI-DAQ Remote Device Access Server (RDA) sur windows Seven
Bonjour, Je travaille sur un PC portable sous Windows Seven.Je veux utiliser une carte NI6503 situé sur un PC industriel sous Windows XP. Pour cela, je souhaite mettre en place une connection réseau et...
View ArticleIs NI usb-4431 possible to use in Simulink?
Hi, first post here!I have been having some issues with connecting my NI usb-4431 with simulink and specifically simulinks analog input-block.First som info:device: NI usb-4431driver: NI-DAQmx v...
View ArticleNI 9205 for passive sensor
Hello I am using the Module NI 9205 with a NI cDAQ 9188. I have 7 sensors to connect to the module, among those 3 are passive sensors and rest of the sensors are active sensors. I am using differential...
View ArticleSilver Control for DAQmx Physical Channel not working
Hi everyone, I have a very odd problem: When I build my VI to an EXE, the Silver control element on my front panel does not find any devices, but the standard element that automatically pops up, when...
View ArticleDAQmx, C++, program onDemand output
HI, I have a task configured to do buffered output (N samples, loaded from MAX)now I want to reconfigure it to do single sample OnDemand output DAQmxCheck((DAQmxStopTask)(task),...
View ArticleUSB 6002
Hi, I have a USB-6002 DAQ card that I am trying to use to read an analog 0-10 V signal for pressure from a Vaisala PTB barometer. The barometer is sending out about 3.5 volts when read with a volt...
View ArticleUSB-6210 and Scaling for 12VDC
I've been using a USB-6210 device to monitor some optical readings on a medical device. These signals all have been the range of 0-5VDC. Now I have been asked to also monitor a 12VDC power supply...
View ArticleCvi exe file
Hello I create my application code for an usb 6008 daq. I have my exe file but I want to use in another computer which does not have lab windows installed. Is there a base program that I should install...
View ArticleDAQmxWriteAnalog64 is blocking, must counters be running?
We are using NIDAQmx and the DAQmxWriteAnalog64 function. The application is written in VB6 so uses the C interface to NIDAQ. We understand that DAQmxWriteAnalog64 is a blocking function, and that...
View ArticleDeciding on a mutlifunction DAQ
I'm currently working on a project that will be using 5 pressure sensors (analog inputs) and a usb handheld barcode scanner as my inputs and I will need to drive 12 digital outputs. I will be using the...
View ArticlePressure sensor 6250E
Hi,I have a Honeywell pressure sensor model TJE that is currently connected to a NI 9237 bridge board. I am having to change equipment to a NI PCI-6250E multifunction DAQ with a SCB-68 terminal block....
View ArticleWindows 7 driver for SCXI-1600
Hi, I am trying to use an SCXI system with Windows 7 64 bit. I see my SCXI-1600 card in the Measurement & Automation Explorer (under 'Devices and Interfaces') but the window alongside reports...
View ArticleDAQmx folder in \vi.lib\ missing
I am trying to run DAQmx vis on a fresh installation of LV2014 SP1 (DAQmx Drivers 14.5.1) but the installation does not create the DAQmx folder in the vi.lib so my VIs (developed on a different...
View ArticlePCI 6341 with SCXI 1102B
I have a PCI 6341 connected to a SCXI 1102B (with a SCXI-1303 terminal block). I can read data on ai0, but not any other channel and the SCXI is not shown in NI-MAX as an available accessorie under...
View Article